اثر کسر حجمی مارتنزیت بر خواص خستگی فولاد دوفازی 20B38

نوع مقاله : مقاله پژوهشی

نویسندگان

1 دانشجو/دانشگاه سمنان

2 عضو هیئت علمی/دانشگاه سمنان

3 عضو هیئت علمی/دانشگاه تهران

چکیده

عملیات حرارتی بین دماهای بحرانی یک عملیات مهم و تأثیرگذار در خواص مکانیکی فولاد می باشد. این عملیات یکی از شیوه های آسان و کم هزینه در رسیدن به خواص مکانیکی مطلوب اعم از استحکام و شکل پذیری است. مقاله حاضر اثر عملیات حرارتی بین دماهای بحرانی بر خواص خستگی فولاد میکروآلیاژی بوردار را بررسی می کند. به منظور دستیابی به ریزساختارهای دوفازی با مقادیر متفاوت از مارتنزیت دماهای 730، 750 وc . 770 به عنوان دماهای بین بحرانی انتخاب شدند و بترتیب مقادیر 52،68 و 88 درصد حجمی مارتنزیت در کنار فاز فریت بدست آمد. به منظور بررسی اثر تمپر بر خواص خستگی، یک دسته از نمونه ها تمپر شدند. پژوهش حاضر نشان می دهد که استحکام خستگی با افزایش کسر حجمی مارتنزیت افزایش پیدا می کند و با تمپر کردن استحکام خستگی افت پیدا می کند. کلمات کلیدی: عملیات حرارتی بین دماهای بحرانی،فولاد دوفازی، کسر حجمی مارتنزیت، استحکام خستگی

کلیدواژه‌ها


عنوان مقاله [English]

Effect of volum fraction of martensite on fatigue properties of 20B38 Dual phase steeel

چکیده [English]

Intercritical heat treatment is an important and effective operations on the mechanical properties of steel. This operation is easy and cost effective ways to achieve the desired mechanical properties such as strength and ductility. In this paper, we investigate the effect of Intercritical heat treatment on fatigue properties of microalloying boron steel. In order to achieve different dual phase microstructures with different amounts of martensite, the temperatures of 730 , 750 and 770 0c wase selected as the Intercriticalcritical temperatures and valus of 52 , 68 and 88 % by volume martensite obtained with the ferrite. To investigate the effect of tempering on fatigue properties ,one series of samples were Tampere. The present study shows that the fatigue strength increases with increasing volume fraction of martensite and with tempering the fatigue strength will decrease. Keywords : Intercritical heat treatment , dual phase steel , Martensite volum fraction , Fatigue strength

کلیدواژه‌ها [English]

  • Intercritical heat treatment
  • dual phase steel
  • Martensite volum fraction
  • Fatigue strength
[1]. G. R. Speech, “Dual-phase steels”, Metala Handbook, Vol. 1, 10th Ed., ASM, USA, 1990, pp. 389-423.
[2].M. Tayanç, A. Aytaç, "The effect of carbon content on fatigue strength of dual-phase steels", Materials & DesignVolume 28, Issue 6, 2007, Pages 1827–1835.
[3]. M.A.Maleque,Y.M. Poon , H.H. Masjuki" The effect of intercritical heat treatment on the mecanical propertice of AISI 3115 steel"Jornal of Materials Prrocessing Tecnology 153-154 (2004) 482-487.
[4]. P.C. Chakraborti, M.K. Mitra," Room temperature low cycle fatigue behaviour of two high strength lamellar duplex ferrite–martensite (DFM) steels, International Journal of Fatigue 27 (2005) 511–518.
[5]. "Fractography", Metals Handbook, Vol.12, 9th Ed., ASM, 1987.
[6]. R.M.Nadraki, “National Symposium on Critical and Strategic Materials”,American Chemical Society, 1987, pp. 108-110.
[7]. H.K.D.H. Bhadeshia, "Bainite in steels: transformations,   microstructure   and   propertice",2nded–London, IOM Communications, 2001.
[8]. Mingfei Guan, Hao Yu,"Fatigue crack growth behaviors in hot-rolled low carbon steels: A comparison between ferrite–pearlite and ferrite–bainite microstructures ", Materials Science & Engineering A 559 (2013)875–881.
[9].A. B. Cota, R. Barbosa and D. B. Santos, "Simulation of the controlled rolling and accelerated cooling of bainitic steel using torsion testing" , Jornal of Materialls Processing Technology, Vol.100, 2000, pp.156-162.
[10]. M. Sarwar, E. Ahmad, K. A. Qureshi and T. Manzoor, "Influence of epitaxial ferrite on tensile properties of dual-phase steel", Materials and Design, 2005, pp. 335-340.
[11]. D.J.Wulpi, "Understanding how components fail", 3rd Ed., ASM, 5891.