[1] M. Dubois, “Measurement of the thermoelastic coefficient of metals by strain gauges,” Strain, vol. 14, no. 1, pp. 22–31, 1978.
[2] S. J. Patel, “A century of discoveries, inventors, and new nickel alloys,” JOM J. Miner. Met. Mater. Soc., vol. 58, no. 9, pp. 18–20, 2006.
[3] Y. TANJI, Y. SHIRAKAWA, and H. MORIYA, “Young’s modulus, shear modulus and compressibility of Fe-Ni (fcc) alloys,” Sci. reports Res. Institutes, Tohoku Univ. Ser. A, Physics, Chem. Metall., vol. 22, pp. 84–92, 1970.
[4] Y. Chen, Z. G. Liu, Y. N. Cao, and Z. S. Zhu, “Atom probe microanalysis of an elinvar type alloy,” Scr. Metall., vol. 22, no. 7, pp. 1075–1078, 1988.
[5] W. S. McCain and R. M. Maringer, “Mechanical and physical properties of Invar and Invar-type alloys,” BATTELLE MEMORIAL INST COLUMBUS OH DEFENSE METALS INFORMATION CENTER, 1965.
[6] Z. Kaczkowski, “Influence of thermal and mechanical treatment on internal friction, modulus of elasticity and its temperature stability in NiSPAN C type alloy,” Phys. B+ C, vol. 119, no. 1–2, pp. 125–129, 1983.
[7] O. A. Khomenko and I. F. Khil’kevich, “Effect of chromium and aluminum on the physical and mechanical properties of precipitation-hardening Fe-Mn Elinvar,” Met. Sci. Heat Treat., vol. 24, no. 6, pp. 425–428, 1982.
[8] A. A. Tavassoli, “Effect of precipitation on physical properties of NiSpan C,” Scr. Metall., vol. 7, no. 4, pp. 345–350, 1973.
[9] M. Seifollahi, S. H. Razavi, S. Kheirandish, and S. M. Abbasi, “The mechanism of η phase precipitation in A286 superalloy during heat treatment,” J. Mater. Eng. Perform., vol. 22, no. 10, pp. 3063–3069, 2013.
[10] A. P. M. E.J.Hayes, “the effect of deformation on the magnetoelastic properties of Iron-Nickle alloys and some implications concering correntheries of invar behavioure,” Trans. Magn., vol. vol. Mag-1, 1975.
[11] J. W. M. C. S. Whitecroft, “The Influenceof Chromium Content on the Precipitation of `γ (Ordered Ni3Ti) in Some Austenitic Steels,” METALLOGRAPHY, vol. VOL 2,PP30, 1969.
[12] A. V Sazykina and O. A. Khomenko, “Effect of chromium on the modulus of elasticity and the thermoelastic coefficient of elinvar alloys,” Met. Sci. Heat Treat., vol. 18, no. 12, pp. 1040–1043, 1976.
[13] T. G. A. Khomenko O.A, Sazykina A.V., “Effect of Cobalt on ThePhysicomechanical Properties of Precipitation-Hardening Elinvars,” Met. Sci. Heat Treat., vol. Vol. 22, p, 1980.
[14] E. F. Bradley, “Superalloys: a technical guide,” 1988.
[15] C. T. Sims, N. S. Stoloff, and W. C. Hagel, “superalloys II,” 1987.
[16] Z. G. Liu, T. Al-Kassab, and P. Haasen, “The structure of the γ′-precipitates and the precipitation hardening of an elinvar alloy,” Scr. Metall. Mater., vol. 24, no. 4, pp. 655–660, 1990.
[17] F. Vogel, N. Wanderka, S. Matsumura, and J. Banhart, “Early stages of decomposition within the γ′ phase of a Ni–Al–Ti model alloy,” Intermetallics, vol. 22, pp. 226–230, 2012.
[18] K. Yang, Y. Xie, X. Zhao, C. G. Fan, and Y. Y. Li, “Microstructure and hydrogen embrittlement in incology 907,” Scr. Metall. Mater., vol. 25, no. 10, pp. 2399–2404, 1991.
[19] Z.-X. Yuan, S.-H. Song, Y.-H. Wang, J. Liu, and A.-M. Guo, “Effect of pre-deformation on the age hardening of a niobium-microalloyed steel,” Mater. Lett., vol. 59, no. 16, pp. 2048–2051, 2005.
[20] S. G. Chowdhury, S. Das, and P. K. De, “Cold rolling behaviour and textural evolution in AISI 316L austenitic stainless steel,” Acta Mater., vol. 53, no. 14, pp. 3951–3959, 2005.
[21] B. AN and S. Ranganathan, “Aging behaviour in copper bearing high strength low alloy steels,” ISIJ Int., vol. 44, no. 1, pp. 115–122, 2004.
[22] D. H. Ping, M. Ohnuma, Y. Hirakawa, Y. Kadoya, and K. Hono, “Microstructural evolution in 13Cr–8Ni–2.5 Mo–2Al martensitic precipitation-hardened stainless steel,” Mater. Sci. Eng. A, vol. 394, no. 1, pp. 285–295, 2005.
[23] P. W. Hochanadel, G. R. Edwards, C. V Robino, and M. J. Cieslak, “Heat treatment of investment cast PH 13-8 Mo stainless steel: Part I. Mechanical properties and microstructure,” Metall. Mater. Trans. A, vol. 25, no. 4, pp. 789–798, 1994.
[24] C. V Robino, M. J. Cieslak, P. W. Hochanadel, and G. R. Edwards, “Heat treatment of investment cast PH 13-8 Mo stainless steel: part II. Isothermal aging kinetics,” Metall. Mater. Trans. A, vol. 25, no. 4, pp. 697–704, 1994.
[25] Y. Zhang, X. Tian, Z. Qin, and H. Jiang, “Temperature compensating Elinvar character in Fe–Mn–Si alloys,” J. Magn. Magn. Mater., vol. 324, no. 5, pp. 853–856, 2012.
[26] م. حسنی, “نگاهی به خواص مکانیکی و فیزیکی سوپر آلیاژهای پایه نیکل,” دانششکده مهندسی، دانشگاه سمنان, 1385.
[27] F. R. N. Nabarro and M. S. Duesbery, Dislocations in solids, vol. 11. Elsevier, 2002.
