@article { author = {kharazmipoor, hossein and ranjbar, khalil}, title = {The Effects of Simultaneous Addition of Chromium Oxide (Cr2O3) and Niobium Oxide (Nb2O5) on Microstructures and the Zirconia Phase Stability of Al2O3-10%ZrO2 Composite}, journal = {Metallurgical Engineering}, volume = {21}, number = {4}, pages = {300-311}, year = {2018}, publisher = {Iranian Metallurgical Engineers}, issn = {1563-1745}, eissn = {}, doi = {10.22076/me.2019.86668.1192}, abstract = {The present research aimed to study the effects of simultaneous and separate addition of niobium oxide and chromium oxide on microstructures, the tetragonal zirconia phase stability, and sintered density of alumina-zirconia composite. The powder metallurgy method was used to prepare the powder of desired composites. To this end, alumina and zirconia powders (with a constant weight of 10%) were used as the main materials and 1% niobium oxide and 0.6% chromium oxide powders were applied as additives. Powdered composite samples were centrally pressurized into a mold and then were sintered at 1300-1500°C. The phases were identified using the X-ray diffraction and microstructures were studied by a scanning electron microscope. Sintered density, hardness, grain size, and the number of zirconia phases were also calculated. The results showed that hardness and sintered density substantially increase with the addition of niobium oxide and chromium oxide, as the density and hardness of the sample containing 1% niobium oxide and 0.6% chromium oxide powders were obtained 3.72 g/cm3 and 1263 HV, respectively. The density and hardness of samples increased with the addition of niobium oxide and chromium oxide. In addition, the simultaneous addition of niobium oxide and chromium oxide to alumina-zirconia composite reduced the sintering temperature by 100°C. The alumina grain size increased with the addition of a certain weight percent of niobium oxide and chromium oxide. However, the effects of niobium oxide were greater, as it caused the growth of alumina grains and instability of the tetragonal zirconia phase.}, keywords = {alumina-zirconia composite,Chromium oxide,niobium oxide,Tetragonal phase,sinter}, title_fa = {تاثیر افزودن همزمان اکسیدهای (Nb2O5,Cr2O3) برریزساختار و پایداری فاز زیرکونیا درکامپوزیت Al2O3-10%ZrO2}, abstract_fa = {این تحقیق تاثیر افزودن همزمان و جداگانه اکسیدهای نیوبیوم و کروم بر ریزساختار، پایداری فاز تتراگونال زیرکونیا و چگالی زینتر کامپوزیت آلومینا-زیرکونیا مورد مطالعه قرار گرفت. از روش متالوژی پودر برای تهیه پودر کامپوزیت های مربوطه استفاده گردید. بدین منظور از پودر های آلومینا و زیرکونیا ( با 10درصد وزنی ثابت) به عنوان مواد اصلی و از پودرهای اکسیدنیوبیوم 1 درصد وزنی و اکسیدکروم 6/0درصدوزنی به عنوان عناصر افزودنی استفاده شد. نمونه های پودری کامپوزیت ها بصورت محوری تحت فشار درون قالب قرار گرفته و سپس در دمای 1300 تا 1500 درجه سانتیگراد در محیط هوا زینتر شدند. در شناسایی فازها از پراش اشعه ایکس و برای بررسی ریزساختارها از میکروسکوپ الکترونی روبشی استفاده شد. چگالی زینتر، سختی، اندازه دانه و میزان فازهای زیرکونیا محاسبه گردید. بررسی ها ونتایج آزمون ها نشان داد که سختی و چگالی زینتر با افزودن اکسیدهای نیوبیوم و کروم افزایش قابل ملاحظه ای پیدا کرده است و چگالی و سختی نمونه ای که دارای 1 درصد وزنی اکسید نیوبیوم و 6/0 درصد وزنی اکسیدکروم است به ترتیب برابر با g/cm3 72/3 و HV 1263 بدست آمد. چگالی و سختی نمونه ها با افزودن اکسیدهای نیوبیوم و کروم افزایش و افزودن همزمان اکسیدهای نیوبیوم و کروم به نمونه آلومینا-زیرکونیا دمای زینتر حدود 100 درجه سانتیگراد کاهش یافت. اندازه دانه های آلومینا با افزون درصد وزنی از اکسیدهای نیوبیوم و کروم افزایش یافت. این میان تاثیر اکسید نیوبیوم بسیار شدیدتر بوده و موجب رشد دانه های زمینه آلومینا و همچنین ناپایداری فاز تتراگونال زیرکونیا نیز شده است.}, keywords_fa = {کامپوزیت آلومینا-زیرکونیا,اکسیدکروم,اکسیدنیوبیوم,زینتر,فاز تتراگونال}, url = {https://www.metalleng.ir/article_35170.html}, eprint = {https://www.metalleng.ir/article_35170_d2a3820df4100e84a221ada747546d03.pdf} }