@article { author = {Javadzadeh Kalahroudi, Faezeh and Koohdar, Hamidreza and Shirazi, Hassan and Jafarian, Hamidreza and Nili-Ahmadabadi, Mahmoud}, title = {Effect of Severe Plastic Deformation byHigh Pressure Torsion on the Microstructure, Mechanical Properties and Pseudoelastic Behavior of the Fe-10Ni-7Mn (wt.%) Steel after Intercritical Annealing treatment}, journal = {Metallurgical Engineering}, volume = {21}, number = {3}, pages = {176-186}, year = {2018}, publisher = {Iranian Metallurgical Engineers}, issn = {1563-1745}, eissn = {}, doi = {10.22076/me.2018.91387.1201}, abstract = {In this research, the effect of severe plastic deformation by high pressure torsion process on the microstructure, mechanical properties and pseudoelastic behavior of the Fe-10Ni-7Mn (wt.%) alloy after annealing at intercritical temperatures was investigated. The results revealed that applying high pressure torsion process for 20 turns on the solution annealed specimen and intercritical annealed samples at two different temperatures, 580 and 600°C for 2 hours, caused reasonable ductility with significant increase in micro-hardness, ultimate tensile strength and reduced grain size to nanometer. Phase evaluation by XRD and EBSD analysis showed that high pressure torsion process led to reverse transformation of martensite to austenite in solution annealed specimen and austenite to martensite transformation in the intercritical annealed samples. Among studied samples conducted in this research, the intercritical annealed sample at 600°C and subsequently deformed by high pressure torsion, revealed the most significant mechanical properties. Moreover, in this sample due to the higher fraction of austenite, fine grain size and high tensile strength, and easier reversible movement of the fcc/hcp interface, more amount of pseudoelasticity was achieved in comparison to the others samples.}, keywords = {Fe-10Ni-7Mn (wt.%) Low carbon martensitic steel,High pressure torsion,Intercritical annealing in the dual-phase region,Mechanical properties,Psuedoelastic behavior}, title_fa = {تاثیر انجام تغییرشکل پلاستیک شدید به روش پیچش تحت فشار بالا بر ریزساختار، خواص مکانیکی و رفتار سودوالاستیسیته فولاد Fe-10Ni-7Mn (wt.%)آنیل‌شده در منطقه دو فازی آستنیت-فریت}, abstract_fa = {در پژوهش حاضر، تاثیر تغییرشکل پلاستیک شدید به روش پیچش تحت فشار بالا به همراه آنیل در منطقه دو فازی فریت-آستنیت بر ریزساختار، خواص مکانیکی و سودوالاستیسیته فولاد مارتنزیتی کم کربن Fe-10Ni-7Mn (wt.%) مورد بررسی قرار گرفت. بدین منظور نمونه ها در سه حالت پس از آنیل محلولی و آنیل هم دما در دماهای ℃ 580 و 600 به مدت 2 ساعت در معرض فرآیند پیچش تحت فشار بالا قرار گرفتند. نتایج حاکی از آن است که اعمال 20 دور فرآیند پیچش تحت فشار بالا بر نمونه های آنیل محلولی و آنیل شده موجب بهبود چشمگیر سختی و استحکام نهایی، کاهش اندازه دانه به ابعاد نانومتری و دستیابی به چکش خواری مطلوب شده است. بررسی های فازی نشان داد که فرآیند پیچش تحت فشار بالا موجب رخداد دگرگونی معکوس مارتنزیت به آستنیت در نمونه آنیل محلولی و دگرگونی آستنیت به مارتنزیت در نمونه های آنیل شده در منطقه دوفازی آستنیت-فریت شده است. در مقایسه سه نمونه مورد مطالعه، نمونه آنیل شده در دمای C° 600 و سپس فرآوری شده با فرآیند پیچش تحت فشار بالا، سختی مطلوبتر با بیشترین میزان یکنواختی و همچنین استحکام نهایی و تغییرطول تا شکست بهینه ای نسبت به دو نمونه دیگر ارائه داد. به دلیل درصد آستنیت بیشتر موجود در ریزساختار این نمونه، اندازه دانه کوچک و استحکام نهایی بیشتر، امکان حرکت برگشت پذیر فصل مشترک فازهای آستنیت و مارتنزیت اپسیلن بهتر مهیا شد و در نتیجه میزان سودوالاستیک به دست آمده از این نمونه نسبت به دو حالت دیگر اندکی بیشتر بوده است.}, keywords_fa = {فولاد مارتنزیتی کم کربن Fe-10Ni-7Mn (wt.%),پیچش تحت فشار بالا,آنیل در منطقه دو فازی,خواص مکانیکی,رفتار سودوالاستیسیته}, url = {https://www.metalleng.ir/article_34335.html}, eprint = {https://www.metalleng.ir/article_34335_acef1a296b23c5a6b1a15608803ff9ac.pdf} }