@article { author = {Zamani, Mohammad and Hosseinabadi, Fereshteh and Abutalebi, Mohammad Reza and Seyedein, Seyed Hossein}, title = {The effect of copper on the microstructure and mechanical properties of Bio Zn-Cu alloy}, journal = {Metallurgical Engineering}, volume = {24}, number = {3}, pages = {206-215}, year = {2021}, publisher = {Iranian Metallurgical Engineers}, issn = {1563-1745}, eissn = {}, doi = {10.22076/me.2022.545378.1341}, abstract = {In this study, the effect of copper on the microstructure and mechanical properties of the Zn-xCu (x= 1,2 and 3.5 Wt.%) bioalloy were investigated. The extrusion was performed on Zn-xCu alloys with speed of 2 mm/min at a temperature of 240 °C to improve microstructure and mechanical properties. The extrusion ratio was considered to be 5 to 1. In order to investigate the effect of copper on the mechanical properties of this alloy such as yield strength, tensile strength and relative elongation percentage, the extruded specimens were subjected to uniaxial tensile test at room temperature. The results of tensile test showed that the highest yield strength, ultimate strength and elongation were obtained by Zn-3.5Cu alloy which is 215MPa, 234 MPa and 46%, respectively, which meets the general design criteria for cardiovascular stents. Scanning Electron Microscope images showed that as the Cu content increases, more CuZn5precipitates were formed. Microstructural studies show that with increasing the copper content, the secondary phase distribution in the matrix increases and during the extrusion process, the secondary phases are crushed and stretched in the extrusion direction, which increases the yield stress and tensile strength of the alloy with higher copper content.}, keywords = {Zn-Cu alloy,copper content,extrusion,Mechanical properties,cardiovascular stent}, title_fa = {بررسی تاثیر مس بر ریزساختار و خواص مکانیکی بیوآلیاژ Zn-Cu}, abstract_fa = {در این تحقیق به بررسی تاثیر مس بر ریزساختار و خواص مکانیکی بیوآلیاژZn-Cuپرداخته شده‌است.عملیات ترمومکانیکی اکستروژن به‌منظور بهبود ریزساختار و خواص مکانیکی بر آلیاژهای با درصدهای مختلف مس صورت گرفت. فرآیند اکستروژن با سرعت2 میلیمتر بر دقیقه و در دمای°C240 و با نسبت اکستروژن 5 به 1 انجام شد. به‌منظور بررسی تاثیر مس بر خواص کششی آلیاژ مذکور نظیر استحکام تسلیم، استحکام کشش و درصد ازدیاد طول نسبی، نمونه­های اکسترود شده تحت آزمایش کشش تک­محور در دمای اتاق قرار گرفتند. نتایج آزمایش کشش نشان داد که بیشترین مقدار استحکام تسلیم  MPa215، استحکام نهاییMPa 234 و ازدیاد طول نسبی% 46 مربوط به آلیاژ Zn-3.5Cu بوده است که معیارهای طراحی کلی برای استنت‌های قلبی عروقی را برآورده می‌کند. تصاویر ریز ساختار حاصل از میکروسکوپ الکترونی روبشی نشان داد که با افزایش غلظت مس، فازCuZn5 بیشتری رسوب کرده است. مطالعات ریزساختاری حاکی از آن است که با افزایش درصد مس توزیع فازثانویه در زمینه بیشتر شده و حین فرآیند اکسترود فازهای ثانویه خرد شده و در جهت اکسترود کشیده شده‌اند و همین امر سبب افزایش تنش تسلیم و استحکام کششی در آلیاژ با درصد مس بیشتر می‌شود.  }, keywords_fa = {آلیاژ Zn-Cu,غلظت مس,اکستروژن,خواص مکانیکی,استنت قلبی عروقی}, url = {https://www.metalleng.ir/article_254950.html}, eprint = {https://www.metalleng.ir/article_254950_8d2a6e1c5df15ad7dcdda6746c0a2732.pdf} }