@article { author = {Khorshidi Fard, Mohammad Rasool and Abedini, Morteza}, title = {Corrosion, erosion and erosion-corrosion behavior of SiC reinforced Ni-P coating on the surface of X65 steel}, journal = {Metallurgical Engineering}, volume = {24}, number = {2}, pages = {110-121}, year = {2021}, publisher = {Iranian Metallurgical Engineers}, issn = {1563-1745}, eissn = {}, doi = {10.22076/me.2022.534520.1326}, abstract = {In the present paper, corrosion, erosion and erosion-corrosion behavior of Ni-P-SiC composite coatings on the surface of X65 carbon steel were investigated. The coatings were produced in an electroless solution containing 0, 5, 10, and 15 g/l SiC particles. The prepared coatings were studied using scanning electron microscopy (SEM), X-ray diffraction (XRD) and microhardness measurements. Polarization tests in a stagnant solution and during erosion-corrosion were also performed to characterize the corrosion behavior of various coatings. Erosion-corrosion and pure erosion tests were carried out using a slurry impingement rig at an impingement angle of 90° under a jet velocity of 6.5 m/s and the synergy parameters were then calculated. SEM images and XRD results showed an increase in the amount of embedded SiC particles in the coatings by increasing the concentration of SiC particles in Ni-P bath up to 10 g/l. Further increase in the SiC concentration in the electroless bath had less effect on the amount of embedded SiC in the coatings. Polarization tests during erosion-corrosion revealed that the embedded SiC particles could largely lower the corrosion rate of the composite coatings as compared with Ni-P coating.  The results also showed that the addition of SiC particles in the coating resulted in a significant decrease in the erosion and erosion-corrosion rates. This was attributed to the limited plastic deformation on the surface of the composite coating as a result of the presence of SiC particles.  }, keywords = {Electroless Ni-P coating,Ni-P-SiC coating,Corrosion,erosion,Erosion-corrosion}, title_fa = {رفتار خوردگی، رفتگی و رفتگی-خوردگی پوشش نیکل-فسفر حاوی ذرات SiC روی سطح فولاد X65}, abstract_fa = {هدف این تحقیق بررسی رفتار خوردگی، رفتگی و رفتگی-خوردگی پوشش­های نیکل-فسفر حاوی ذرات SiC روی سطح فولاد  X65 است. پوشش­دهی در حمام­های الکترولس حاوی صفر، 5، 10 و 15 گرم بر لیتر انجام شد. پس از آماده­سازی پوشش­ها، بررسی­ها با استفاده از میکروسکپ الکترونی روبشی (SEM)، پراش پرتو ایکس (XRD) و سختی­سنجی انجام شد. همچنین آزمون­های پلاریزاسیون در حالت ساکن و در حین رفتگی روی پوشش­های مختلف انجام گرفت. آزمون­های رفتگی-خوردگی و رفتگی خالص نیز با استفاده از دستگاه جت برخوردی تحت زاویه برخورد 90 درجه و سرعت برخورد 5/6 متر بر ثانیه انجام شد و پارامترهای هم­افزایی رفتگی و خوردگی محاسبه شد. نتایج آزمون XRD و تصاویر SEM بیانگر افزایش مقدار کاربید سیلیسیم در پوشش با افزایش غلظت ذراتSiC  در حمام الکترولس نیکل-فسفر تا 10 گرم بر لیتر بود. افزایش بیشتر غلظت ذرات در حمام تاثیر چندانی بر مقدار ذرات در پوشش نداشت. آزمون­های پلاریزاسیون در حالت رفتگی بیانگر تاثیر زیاد حضور ذرات SiC در کاهش نرخ خوردگی پوشش­های کامپوزیتی در مقایسه با پوشش ساده نیکل-فسفر بود. همچنین نتایج آزمون­های رفتگی و رفتگی-خوردگی نشان داد که افزودن ذرات SiC به پوشش می­تواند منجر به کاهش قابل توجه نرخ رفتگی-خوردگی و نرخ رفتگی شود. این موضوع به نقش ذرات SiC در محدود کردن تغییر شکل پلاستیک ناشی از برخورد ذرات ساینده حین آزمون رفتگی و رفتگی-خوردگی در سطح پوشش کامپوزیتی نسبت داده شد.}, keywords_fa = {پوشش الکترولس Ni-P,پوشش Ni-P-SiC,خوردگی,رفتگی,رفتگی- خوردگی}, url = {https://www.metalleng.ir/article_249431.html}, eprint = {https://www.metalleng.ir/article_249431_214ce2037aabde0a18d8a78ec23666a2.pdf} }