@article { author = {Fatemi, Seyed Mahmood and kazemi Asl, Ali Akbar and Abedi, Amir}, title = {The effect of pre-existing twin on the shear deformation behavior of AZ31 magnesium alloy}, journal = {Metallurgical Engineering}, volume = {23}, number = {4}, pages = {328-337}, year = {2020}, publisher = {Iranian Metallurgical Engineers}, issn = {1563-1745}, eissn = {}, doi = {10.22076/me.2021.141433.1303}, abstract = {In this research, the shear deformation behavior of an AZ31 magnesium alloy was studied at a temperature range of 200-440 °C by employing shear punch testing method. To introduce twins, a rolled alloy was pre-strained, and the shear deformation of pre-twinned material was compared with the annealed one. The results showed that pre-existing twins led to a higher shear strength owing to the strengthening role of twin boundaries. At 320 °C, due to the activation of nonbasal slip systems, the twin boundaries act as dislocation sink and facilitate dynamic recovery. At high temperatures, as the twins were simply recovered no appreciable difference in deformation behavior and final microstructure could be realized between the alloys with and without twins. Twin boundaries provide more frequent nucleation sites for new grains and also deformation inhomogeneities, increasing the fraction of new grains at 200 and 260 °C. Finer recrystallized grains were obtained during shear deformation, compared to those compression /tension at similar conditions. The latter was discussed relying on the role of shear strain in evolution of fine microstructures.}, keywords = {Twinning,shear behavior,slow stress,Recrystallization}, title_fa = {مطالعه تاثیر دوقلویی های اولیه بر رفتار تغییرشکل برشی آلیاژ منیزیم AZ31}, abstract_fa = {در این پژوهش رفتار برشی آلیاژ منیزیم AZ31 در بازه دمایی °C 440-200 با استفاده از آزمایش پانچ برشی مورد مطالعه قرار گرفت. جهت ایجاد دوقلویی های اولیه، آلیاژ نورد شده تحت پیش کرنش قرار گرفته و رفتار تغییرشکل برشی آن با نمونه های بدون دوقلویی مقایسه شد.  نتایج نشان می دهند که آلیاژ حاوی دوقلویی در دماهای °C 200 و 260 بدلیل نقش کارسخت کنندگی مرزهای دوقلویی ها استحکام بالاتری را نسبت ماده بدون دوقلویی های اولیه نشان می دهد در حالیکه در دمای °C 320 با فعال شدن سیستم های ثانویه نقش مرزهای دوقلویی به عنوان جذب کننده نابجایی ها حاکم شده و به بازیابی دینامیک کمک می نماید. در دماهای بالاتر باتوجه به بازیابی شدن دوقلویی ها تفاوت محسوسی در رفتار تنش سیلان برشی و ساختار نهایی دو آلیاژ (حاوی و بدون دوقلویی اولیه) مشاهده نشد. مرز دوقلویی های اولیه به دلیل در اختیار گذاشتن مکانهای مرجح جوانه زنی دانه های جدید و ایجاد ناهمگنی تغییرشکلی بیشتر  منجر به افزایش کسر دانه های تبلور مجدد در دماهای °C 200 و 260 گردید. اندازه دانه های بدست آمده در آزمایش پانچ برشی  نسبت به شرایط مشابه در آزمایش های فشار و کشش بسیار ظریف تر می باشد. این مشاهد با توجه به نقش کرنش های برشی در توسعه ساختارهای ظریف دانه مورد بحث واقع شد.}, keywords_fa = {دوقلویی,رفتار برشی,تنش سیلان,تبلور مجدد}, url = {https://www.metalleng.ir/article_244673.html}, eprint = {https://www.metalleng.ir/article_244673_94553eccd63304d9c1bb7204811606b0.pdf} }